Has Markforged Continuous Fiber Replaced Machined Aluminum in 2026?
Not every part, and not every application. But for one category most engineers don't realize qualifies, the honest math has moved: brackets, end-of-arm tooling, inspection fixtures, and low-volume structural parts that fit on the print bed.
If you ruled out FDM because it was "prototype only" in 2020, the platform has changed. Markforged's continuous fiber reinforcement (CFR) lays unbroken strands of carbon fiber inside an Onyx part, right where the loads run. For brackets, EOAT, and fixtures under about 100 units, it now often beats machined aluminum on weight, lead time, and total cost.
The honest math
Continuous carbon fiber reinforced parts reach a flexural strength of about 540 MPa and flexural stiffness of about 60 GPa. That puts them in the same range as 6061-T6 aluminum, which has a modulus of roughly 69 GPa.
The difference is density. Onyx and carbon fiber parts come in at roughly 1.2–1.4 g/cm³, versus 2.7 g/cm³ for aluminum. That means a printed part typically weighs about half as much as the same aluminum part, and often less once you strip out material that only existed for machining. Markforged reports a strength-to-weight ratio about 50% higher than 6061 aluminum in flexure.
Then there's time. A print-ready file becomes a part in 24–48 hours, with no fixturing, no setup, and no waiting in a loaded CNC queue that can stretch to weeks.
Where continuous fiber wins
- Weight-sensitive structural brackets in aerospace, drones, and robotics, where every gram costs flight time or payload.
- End-of-arm tooling (EOAT). Lighter grippers and jaws let a robot move faster, carry more, or run on a smaller motor.
- Inspection fixtures and CMM holders. Carbon fiber's low thermal expansion helps fixtures stay true in a shop that warms and cools.
- Low-volume structural parts (1–50 units), where machining setup and fixturing costs never get amortized.
- Part consolidation. Assemblies of several machined pieces can often be printed as one part.
- Legacy replacement parts. Obsolete brackets for older equipment can be scanned or modeled and reprinted on demand.
- Load-path fiber routing. You put fiber exactly where the part needs strength, instead of carving it out of a solid block.
Where aluminum still wins
- Large parts. Anything bigger than the FX20's 525 × 400 × 400 mm build volume.
- High service temperatures. Polymer parts have limits; above roughly 150°C, aluminum is the safer choice.
- High volumes. Production runs of a few hundred or more of a simple geometry, where machining setup cost is spread thin.
- Tight mating surfaces. Precision faces held to better than ±0.1 mm across the part.
- Isotropic loading. Printed parts are strongest along the fiber and weakest between layers. If the load direction is unpredictable, or the part sees high-cycle fatigue or heavy bolted joints, aluminum doesn't care which way you push it.
X7 vs FX20: which printer for which job
| Printer | Build volume | Best for |
|---|---|---|
| Markforged X7 | 330 × 270 × 200 mm | The production workhorse: brackets, EOAT, fixtures, and most everyday tooling |
| Markforged FX20 | 525 × 400 × 400 mm | Larger parts, aerospace tooling, and ULTEM 9085 with continuous fiber in a chamber heated up to 200°C |
Quick decision checklist
Continuous fiber is worth a serious look if most of these are true:
- The part fits inside the X7 or FX20 build volume.
- You need fewer than about 100 units.
- Weight matters, or lead time matters more than unit cost.
- Service temperature stays under about 150°C.
- Loads follow a predictable path you can route fiber along.
- No mating face needs tolerance tighter than ±0.1 mm.
If several are false, machined aluminum is probably still the right call.
The aluminum default is slipping
Continuous fiber hasn't replaced machined aluminum across the board, and it won't. But for brackets, EOAT, and fixtures under 100 units, Markforged usually wins the honest math. If your shop still defaults to aluminum for every one of those parts, it's worth running the numbers again.
Want the full technical breakdown, including the Markforged vs Stratasys vs UltiMaker decision framework? Read the full comparison here.

No comments:
Post a Comment